DJIFix tool repairing corrupt DJI drone video file on Windows computer

DJIFix for Windows: Repair Corrupt DJI Drone Video for Free

If your DJI drone just spat out a corrupt file, djifix for windows is the free command-line tool that can bring it back. I have burned more hours than I care to count on drone footage that died mid-shoot, and DJIFix is the one tool I trust before I ever consider paying for repair software. Here is exactly how to run it on Windows and get your clip back in full quality.

AspectKey Takeaway
Best free toolDJIFix is free and open source, and it preserves your full quality.
Where to get itDownload the djifix.exe file straight from live555.com.
How to run itDrop the exe in the same folder as the video and run it in Command Prompt.
What it outputsA repaired .H264 stream, which FFmpeg converts back to a playable MP4.
Paid softwareCosts $25 to $67 per file and can lower quality; DJIFix does it free.

Why DJI Drone Files Go Corrupt on Windows

Your drone writes video as a stream of raw data, and the file wrapper that makes it playable gets finalized only when recording stops cleanly. The moment a battery dies, the drone powers off mid-write, or the card is pulled while the camera is still flushing data, the wrapper never gets written. Windows sees a file with no valid header and calls it corrupt. The footage is often still there, sitting behind a broken container.

I learned this the hard way on a client shoot where the drone cut out on the last battery and I nearly told the client their opening shot was gone. It was not gone. The data was intact, the wrapper was just toast, and a free tool got it back. That is the situation DJIFix is built for.

What DJIFix Actually Does

DJIFix is a tiny open-source utility from live555.com that repairs MP4 and MOV files from DJI drones, including the Spark, Mavic Air, Mavic Pro, and Inspire lines. It reads the broken file, salvages the usable video stream, and repackages it as a .H264 file. It does not give you a finished MP4; it hands you a clean stream that FFmpeg then converts back into a fully playable, full-quality MP4.

That two-step process is the entire trick. Most paid tools do the same repair under the hood and charge you per file for the privilege. DJIFix gives you step one free, and FFmpeg gives you step two free, and together they match or beat what the paid software does, without the quality loss some of those tools introduce when they recompress.

How to Run DJIFix on Windows, Step by Step

This is a command-line tool, which sounds scarier than it is. Once you do it once, it takes under a minute.

Step 1: Download djifix.exe

Head to live555.com, grab the DJIFix Windows binary, and save it somewhere easy to reach, like your Downloads folder. There is no installer and nothing to pay for.

Step 2: Put the Tool Next to Your Video

Copy djifix.exe into the same folder as the corrupt video file. It needs to see both files in one place, so this step is not optional.

Step 3: Open Command Prompt in That Folder

In Windows Explorer, click into the folder, type cmd into the address bar, and hit Enter. A Command Prompt opens already pointed at that folder, which saves you a lot of typing.

Step 4: Run the Repair Command

Type the name of the video file and run it:

djifix your-video-filename.MP4

Replace your-video-filename.MP4 with the actual file name, matching the case. The tool prints what it salvages and writes a new .H264 file next to your original.

Step 5: Convert the .H264 Back to MP4 With FFmpeg

Run this in the same Command Prompt to rebuild a playable file:

ffmpeg -i your-video-filename.h264 -c copy your-video-filename-repaired.mp4

The -c copy flag keeps the original quality and runs fast. When it finishes, you have a working MP4 at full quality, ready for your editor. If you do not have FFmpeg installed yet, grab it from ffmpeg.org, and it takes about a minute to set up.

DJIFix vs Paid DJI Repair Software

I want to be straight with you about the paid options. They work, and they are easier if the command line makes you nervous. But they typically run $25 to $67 per corrupted file, and some of them recompress the output, which means you can end up paying money and losing quality at the same time. DJIFix is free and keeps the original stream untouched, and the only cost is learning one command.

My rule is simple: run DJIFix first. If it does not bring the file back, then and only then consider paid software, because at that point the file is likely beyond what a container repair can fix. In my experience DJIFix recovers the vast majority of files that are corrupted by a power loss or a card pulled too early.

How to Stop Losing Footage in the First Place

The best fix is prevention, and most corruption comes down to two things: a card that cannot keep up with the write speed, and pulling the card before the drone fully finishes writing. A reliable card and a clean backup habit will save you more footage than any repair tool.

For drone work I run a SanDisk 128GB Extreme microSD (UHS-I, V30), which is fast enough to handle high-bitrate drone recording without dropping writes. I move footage through a USB-C dual-slot SD/microSD card reader so I am not yanking cards in and out of a flimsy slot, and I back everything up to a Samsung T7 1TB portable SSD the same day. A good card, a clean reader, and a backup drive are a lot cheaper than losing a paid shoot.

Some links above are affiliate links. If you buy through them, I may earn a small commission at no extra cost to you. I only recommend gear I use myself.

Frequently Asked Questions

Is DJIFix safe to use?

Yes. It is open-source software from live555.com, it runs locally on your machine, and it never uploads your footage anywhere. It only reads your local video file and writes a new one beside it.

Does DJIFix work for all DJI drones?

It supports the files produced by the Spark, Mavic Air, Mavic Pro, and Inspire lines, which covers most modern DJI drones. If your model is not listed, the tool still often works, because the repair targets the common DJI MP4/MOV structure.

What if DJIFix does not fix my file?

If the container repair fails, the video stream itself may be damaged. Try a paid repair tool as a last resort, or check whether your drone has a media recovery option. Do not re-record over the card until you have tried recovery.

Do I need to know programming to use DJIFix?

No. You type one command with your file name. That is the whole requirement, and the steps above walk you through it.

Why does my video play on the drone but not on my computer?

The drone plays its own footage from its own encoder, but the file wrapper was never finalized, so desktop players reject it. That is exactly the corruption DJIFix repairs.

Will DJIFix reduce my video quality?

No. It repackages the original stream and FFmpeg copies it without recompressing, so you keep the full quality your drone recorded.

Get Your Footage Back

That corrupt DJI file is probably not lost. Download DJIFix, run the single command, and convert the result with FFmpeg, and you are usually back in business in a few minutes. Save the DJI repair walkthrough so you have the exact commands the next time a card comes out wrong.

I remember pulling a card after a long day of filming and watching half the clips refuse to open. I was sure the work was gone until DJIFix handed me back the footage in full quality. That is the moment I stopped being afraid of a command line and started trusting the free tools that actually work.

Thanks, Mark.

Share this post